CAME FERNI Swing Gate Motor Kit | High-Performance Articulated Arm

cameproducts — Fri, 01 Dec 2017 14:42:34 +0000

The CAME Ferni Automation Kit is a powerful, heavy-duty articulated-arm swing gate operator series. Engineered explicitly for deep-set gates and massive structural brick or stone pillars where standard linear rams cannot physically operate, the Ferni easily reaches around wide masonry.

The system is optimized for heavy residential gates, large estate entrances, and multi-user perimeters, driving gate leaves up to 4.0 meters in length or up to 800 kg in weight per leaf.

Core Engineering & Mechanical Design

Large Pillar Offset Solution: Purpose-built to clear severe architectural challenges, the Ferni can handle extreme hinge-to-wall mounting profiles, reaching around wide pillars with an internal offset distance (C-max dimension) of up to 380 mm without needing to cut structural niches into the stone.
Dual-Voltage Configurations:
- 24V DC Models (FE4024V / FE4024): Built for continuous intensive service profiles. Runs cool under constant loads and natively integrates with an optional emergency backup battery kit (LB180) to keep the property fully automated during a power outage.
- 230V AC Models (FE40230V / FE40230): High-inertia single-phase motors that deliver massive mechanical torque to push heavy, wind-resistant or fully boarded gates.
Intelligent Safety Hub: The 24V variants incorporate an advanced electronic tracking encoder managed via modern ZLX24-series control panels. This delivers active anti-crush obstacle sensing, customizable deceleration slowdown zones to prevent gate slams, and adaptive speed calibration to handle high wind drag.
Rugged Anodized Transmission Arms: The heavy-duty articulated arm assembly is engineered from robust anodized steel and aluminium alloys to resist shearing forces, driving massive gates smoothly while keeping mechanical trap hazards low.

Technical Specifications Matrix

Feature/Model Specification	Ferni 24V Variant (FE4024V)	Ferni 230V Variant (FE40230V)
Max Leaf Length / Weight Limits	4.0m @ 400 kg \| 3.0m @ 450 kg \| 2.0m @ 800 kg	4.0m @ 400 kg \| 3.0m @ 450 kg \| 2.0m @ 800 kg
Maximum Hinge-to-Wall Offset	Up to 380 mm (14.9 Inches)	Up to 380 mm (14.9 Inches)
Power Input / Motor Drive	230V AC (50/60 Hz) / 24V DC	230V AC (50/60 Hz) / 230V AC
Maximum Torque Output	320 Nm	400 Nm (High-Inertia Thrust)
90° Maneuvering Velocity	Fully Adjustable (16 to 45 Seconds)	34 Seconds
Duty Cycle Profile	Intensive Use (Continuous)	30% Semi-Intensive Use
Ingress Protection Rating	IP54 Weatherproof Housing	IP54 Weatherproof Housing

Standard Kit Box Contents

1 x Master 24V or 230V Motor Assembly: Houses the primary electromechanical drive unit, travel limit microswitches, and an ergonomic manual key-release layout.
1 x Slave 24V or 230V Motor Assembly: High-torque secondary gearmotor unit.
2 x Heavy-Duty Articulated Transmission Arms: Solid steel arm linkages engineered to transfer massive motor torque cleanly around extra-deep pillar corners.
1 x Advanced Control Board: Dual-leaf control framework (ZLX24 for 24V kits / ZLX230 for 230V kits) with an LCD setup display, automated safety circuit self-testing, and multi-user memory slots.
1 x AF43S Frequency Card: Plug-in 433.92 MHz radio frequency receiver card.
1 x Pair of DIR10 Safety Photocells: Surface-mounted, synchronized infrared safety beams with a standard 10-meter range for clear driveway threshold defence.
2 x TOP SPORT (TOP44RBN) High-Security Transmitters: Sleek, carbon-fibre textured 4-button rolling code remotes running on a secure 433.92 MHz link to block signal cloning.
1 x TOP-A433N Tuned Antenna: External coaxial antenna to bypass thick masonry interference and maximize remote operational range.

CAME Ferni – Pair Kit

CAME Ferni – Single Kit

Ferni 230v Kit – CAME Gate Automation & Intercom Systems UK | Came Products

CAME FERNI Swing Gate Motor Kit | High-Performance Articulated Arm

Core Engineering & Mechanical Design

Technical Specifications Matrix

Standard Kit Box Contents